Guide of SPC Flooring Care, Clean, and Maintenance(2)

Guide of SPC Flooring Care, Clean, and Maintenance(2)

What you should be looking for here is the material used for the protector.

Most rubber pads or protectors contain antioxidant compounds to make them last longer without becoming brittle. However, this antioxidant compound will produce a chemical reaction when it comes into contact with SPC flooring, resulting in yellow staining, which is called "antioxidant staining."

In addition to yellowing stains, you should also avoid using discoloration preservatives, because the color on it will eventually stain the floor.

As a precaution, take some time to check the materials of the protector, rubber pads, door plugs, and rubber back pads when shopping. Make sure you only buy products that are undyed, unpigmented, or fast-colored, whether it's rubber, nylon or felt.

Generally speaking, for larger size furniture, you need a wider floor protector. So the weight can be evenly distributed. Here is a small tip for you: clean regularly to keep your protector in good condition, and replace it with a new one once it is worn out.

8. Diluted vinegar solution

Some people say that vinegar is acidic and may damage the protective layer of the SPC floor. In fact, vinegar is not only harmless, but also a natural and effective way to keep floors clean. This is also a good way to remove odors on the floor.

9. Use SPC floor polish

Sanding your floor can definitely help maintain a shiny and shiny appearance. Just follow the simple steps here, but be careful not to overdo it.

First sweep the floor to remove debris and dust.

Wipe it off with a mop

Follow the polishing instructions to start polishing your floor.

10. Close the curtains

Long-term exposure to extreme sunlight may cause your SPC floor to fade, become dull or faded. Put down blinds or curtains to protect it from extreme sunlight and heat.

11. Floor cleaning solutions

Using strong chemicals to clean your SPC floors will do more harm than good. It is recommended to use only the cleaner recommended by the SPC floor manufacturer, because it is more effective in cleaning and will not cause too much damage.

Remember, more is not always better. The proper amount of solution is very important to protect the surface layer and prevent passivation. You can also avoid oily, wax or pigment cleaners.

12. Floor waxing

Waxing can sometimes cause many floor problems and problems. Most of the time, the owner used the wrong wax product when the problem occurred.

Speaking of which, you should never try to wax yourself with products such as cream wax.

If you plan to polish or wax your floor, it is safer to seek professional advice and services. Believe me, if your floor is damaged by your own waxing, you definitely want to spend your money on professional waxing instead of replacing a new set of floors.

13. Hire floor professionals

If you have a budget, you must consider hiring professionals to do floor maintenance. Depending on the type of maintenance and service required, it will usually not cost too much to hire a professional team to do these tasks for you every quarter every year.

14. Floor protection with additional coating

In places with heavy traffic and high usage, the wear layer will wear out over time. This is very common in commercial applications. You can say that it is not so necessary for residential floors.

What should you do? As part of routine maintenance, add another layer of finishes to extend the life of your floor.

15. Keep away from direct heat

Most people may not realize this. SPC floors are sensitive to heat. Any direct heat from matches, heating devices and cigarette butts will scar or damage it.

So, the next time you deal with a high-calorie project, make sure you support the carpet or mat on a hot surface without directly touching your SPC floor.

16. Installation after cleaning

It is a bad idea to rinse thoroughly with water immediately after installation. Once installed, if you clean or scrub the floor, you are just destroying your floor.

Normally, it takes a while for the adhesive under the board to dry and stick firmly. It is recommended to isolate the area for at least 48 hours, and some even take a few days, depending on the type of adhesive used.

We are SPC flooring supplier. Please feel free to contact us if you are interested in our products.